توصیف
جزییات
CUAV NEO GPS V2 is a GNSS positioning system, integrating dual-mode GNSS, safety switch, RGB status LEDs, and electronic compass in one to make the drone lighter. It also has the characteristics of high security and strong anti interference.
CUAV NEO GPS V2 adopts built-in I2C bus RGB status LED driver chip and 8 RGB LEDs. After careful design, the LED is integrated
GPS location: UBLOX M8N
RGB status light:
NCP5623C
Compass: IST8310
Buzzer: passive buzzer
Safety switch: physical buttons
Positioning performance
Accuracy: 3D positioning
Refresh rate: 10 Hz (max.)
Acquisition: Cold Start 26S | Hot start 1.5S | 2S power start | Repurchase 1S
Receiver type:
72 channels
GPS / QZSS L1 C / A, GLONASS L10F
BeiDou B1I, Galileo E1B / C
SBAS L1 C / A: WAAS, EGNOS, MSAS, GAGAN
Sensitivity:
Tracking and navigation -167dBm
Cold start -148dBm
Hot start -156dBm
Reacquisition-160dBm
CUAV New Pixhack V5 nano Small Flight Controller for Ardupilot PX4 Drone Parts
V5 nano is an autopilot for spatial constraint applications designed by CUAV in collaboration with the px4 team. It is based on the Pixhawk FMUv5 design standard and is optimized to run PX4 firmware, and it is also compatible with ArduPilot firmware.
Features:
-Compact but powerful V5 nano flight controller + NEO GPS
-Support for hardware on open source platform PX4 and autopilot
-Suitable for fixed-wing drones, helicopters, multicopters, FPVs, VTOL, unmanned boats, UAVs
-High performance: equipped with STM32F765 microprocessor, with 216MHz main frequency, 2M flash and 512K SDRAM. There are four groups of insulation chips and a high precision MS5611 air meter.
-Easy to install and disassemble with 2.6mm gap between IO pins.
-Real-time data monitor: Five groups of built-in sensors enhance its security and stable performance. There are ICM-20689 accelerometer and gyroscope, ICM-20602 accelerometer and gyroscope, BMI055 accelerometer and gyroscope, IST8310 magnetic compass and MS5611 air meter.
Specifications:
Hardware parameters:
-Main UMF processor: STM32F765 processor (32-bit, 216MHz, 2MB flash 512KB RAM)
Sensors:
-Accelerometer: ICM-20602 / ICM-20689 / BMI055
-Gyroscope: ICM-20602 / ICM- 20689 / BMI055
-Magnetometer: IST8310
-Air meter : MS5611
Interfaces:
-UART ports: 5
-I2C ports: 4
-PWM output: up to 11 -PWM input
: 4
-Signal input protocol for Remote Control: PPM / SBUS / DSM
-RC in: 1 -PPM in: 1
-RSSI
input: PWM analog voltage or 3.3V -Bus
standard: 2
-Voltage and current input 1
-On safety: 1
-Puerto GPS: 1
-Puerto debugging: 1
-Puerto JATG: 1
-Port USB: 1 (type C)
compatible Models:
-For Hardware PX4: fixed wing aircraft 3-8 multicópteros , helicopters, VTOLs, UAVs, unmanned boats
Working conditions and physical parameters:
-PM operating voltage: 4.5 to 5.5 V
-USB voltage: 5V ± 0.25 V -Servo input
: 0 to 36V
-Temperature operating temperature: -40 to 85 ° C
Weight and dimensions:
-Dimensions: 40x60x17.5mm
-Weight: 40g
Package 1 included: With NEO GPS
-1 x V5 nano flight controller
-2 x Dupont Cables
-1 ADC6.6 Cable
-2 x I2C /
CAN Cables -1 x SBUS Signal Cable
-1 x RSSI Cable
-1 x DSM Signal
Cable -1 ADC3.3 Cable
-1 x Debug Cable
-1 Safety Switch + Cable
-1 x Voltage Current Cable
-1 x PW-Cable Link Module +
-1 x Power Module -1 x
16GB Memory Card
-1 x I2C Expansion
Board
-1 x TTL Board -1 x NEO GPS
-1 x GPS Bracket
Package 2 included: without NEO GPS
-1 x V5 nano flight controller
-2 x Dupont Cables
-1 ADC6.6 Cable
-2 x I2C /
CAN Cables -1 x SBUS Signal Cable
-1 x RSSI Cable
-1 x DSM Signal
Cable -1 ADC3 Cable. 3
-1 x Debugging Cable
-1 Safety Switch + Cable
-1 x Voltage Current Cable
-1 x PW-Cable Link Module +
-1 x Power Module
-1 16GB Memory Card
-1 x Board I2C Expansion
-1 x TTL Board
Functional:
Advanced jamming
Fast search satellite speed
Safety and integrity protection
Receive up to three GNSS at the same time
Input voltage: 5V
Temperature: -10-70 ° C
توضیحات اضافی
اطلاعات اضافی
| تولید کننده | خیر |
|---|
برچسبها
نظرات
- برای نظر دادن به این محصول اولین باشید
دیدگاه خود را بنویسید.
نظر خودتان را بنویسید
تماس با ما
